Many car owners are very careful when buying auto parts, but it is easy to forget the maintenance of parts after installation. In this way, with the gradual increase of car travel, the parts are very easy to wear and the service time is continuously shortened. Let's learn about the complete collection of maintenance methods of auto parts!
1. Autodíly se bojí, že budou špinavé
If the fuel filter, oil filter, air filter, hydraulic oil filter, various filters and other components are too dirty, the filtering effect will become worse, and too many foreign matters will enter the oil circuit cylinder, resulting in component wear and higher possibility of failure. If there is a serious traffic jam, the vehicle may not work properly. If the radiator fins, air-cooled engine block and head fins, cooler fins and other components are too dirty, the heat dissipation will become worse and the temperature will be too high. Therefore, clean and maintain such "dirty" parts immediately.
2. Tepelná odolnost autodílů
Teplota pístu motoru je příliš vysoká a přehřátí snadno způsobí držení sudu; Pryžová těsnění, klínové řemeny, pneumatiky atd. jsou přehřívané, náchylné k předčasnému stárnutí, sníženému výkonu a zkrácené životnosti; Cívky startéru, generátoru, regulátoru a dalších elektrospotřebičů se přehřívají a snadno se spálí. Ložiska vyřazených vozidel je třeba udržovat při vhodné teplotě. Po přehřátí se mazací olej rychle znehodnotí a nakonec dojde ke spálení ložisek a poškození vozidel.
3. Auto díly strach řetězec
Various couplings of diesel engine system, master-slave gears in the main reducer of drive axle, hydraulically operated valve block and valve rod, valve body and sleeve of full hydraulic steering, etc. These couplings are specially processed and ground in pairs during manufacture. They are very precise. They have been used in pairs throughout their service life and must not be replaced. Piston and cylinder liner, bearing bush and journal, valve and valve seat, connecting rod cylinder head, bearing cap and shaft and other meshing components mesh relatively well with the passage of time. During maintenance, attention should also be paid to assembly in pairs to avoid "approaching" each other.
4. Odolnost vůči strachu
Při instalaci podložky motoru ji neinstalujte v opačném směru. V opačném případě způsobí předčasné poškození ablací. U některých pístních kroužků se speciálními tvary je nelze instalovat obráceně. Sestavte prosím podle požadavků různých modelů; Instalace lopatek ventilátoru má také požadavky na směr. Obecně existují dva druhy ventilátorů: výfukové a sací. Prosím, nedělejte opak. Jinak se zhorší odvod tepla motoru a teplota je příliš vysoká. U pneumatik se směrovým vzorem podobným rybím pneumatikám, aby byla zajištěna velká hnací síla, musí po montáži dráha terénu směřovat přední konec rybí kosti směrem dozadu. Dvě paralelně uspořádané pneumatiky mají různé požadavky podle různých typů vozidel, takže je nelze namontovat náhodně.
5. Nedostatek strachu
When repairing the vehicle, some small objects may accidentally Miss installation. In addition, some people think that it doesn't matter whether it is installed or not. This is very dangerous and harmful. The door locks of the engine must be installed in pairs. For example, sometimes the valve is out of control and damaged by collision with the piston due to missing or missing installation; If there is leakage in the installation of locking devices such as cotter pins, locking screws, bumpers or spring pads installed on engine connecting rod bolts, flywheel bolts and transmission shaft bolts, serious faults may be caused in use. If the oil nozzle used to lubricate the gears in the engine timing gear chamber leaks, the oil leakage from there will become serious and the pressure of the engine oil will become low. If the box cover, oil cover and oil cover are lost, gravel and dust will invade and aggravate the wear of various parts.
6. Ropa se mě bojí
The paper filter element of the dry filter has strong moisture absorption. Once the oil is attached, the mixture with high concentration is easy to be sucked into the cylinder, resulting in insufficient air volume, deterioration of fuel consumption rate, decline of engine output power, and possibly "flying" of diesel engine. If the oil is attached to the triangular tape, it will promote corrosion deterioration, slip easily and reduce the transmission efficiency. If the brake pad, friction plate of dry clutch and brake belt are attached with oil, it is easy to slip or act poorly, threatening driving safety; If the carbon brushes of the starting motor and generator are attached with oil, poor contact will lead to insufficient power of the starting motor and voltage drop of the generator. The rubber of the tire is very sensitive to the corrosion of oil. When contacting with oil, the rubber will become soft and peeling. Short time contact will lead to abnormal and serious damage to the tire.
7. Strach z opakování
Some parts should be disposable, but if individual drivers or repairmen reuse them in order to save or do not know the "taboo", it is easy to cause accidents. Generally speaking, after removing the engine connecting rod bolts, nuts, fixing bolts of imported diesel engine fuel injector, water retaining ring of cylinder liner, sealing copper gasket, various oil seals, sealing rings of hydraulic system, pins and split pins of important parts, the engine cylinder gasket is not damaged during inspection, but it is replaced with a new one. The old ones have poor elasticity, poor sealing and easy aging. They also need to be replaced after long-term use, which is very troublesome. Therefore, if there is a new one, it is better to replace it as much as possible.
8. Bez komprese
Vnější duše pneumatiky musí být naskládána a uchovávána po dlouhou dobu. Pokud se včas neobrátí, dojde k jeho deformaci v důsledku vytlačování a ovlivnění životnosti; Papírové filtrační prvky vzduchového filtru a palivového filtru se při lisování velmi deformují, takže nemohou spolehlivě hrát roli filtru; Olejové těsnění, trojúhelníková páska, vzduchová trubka atd. se nesmí lisovat. Po stlačení se také zdeformuje a ovlivní běžné používání.
9. Strach z ohně
Autodíly zahrnují pneumatiky, trojúhelníkové pásky, kroužek pro zadržování vody ve vložce válce, pryžové těsnění oleje a další pryžové výrobky. Pokud jsou blízko otevřeného ohně, snadno podléhají stárnutí, zhoršují se a poškozují. Na druhou stranu mohou také způsobit požární nehody. Zejména některá vozidla se vznětovým motorem se kvůli chladné zimě obtížně startují. Někteří řidiči musí často topit hořáky, aby se vyhnuli spálení potrubí, olejových okruhů atd.
10. I'm afraid of washing clothes
Někteří lidé, kteří začínají řídit nebo opravovat autodíly, si mohou myslet, že je potřeba vyčistit všechny díly, ale ve skutečnosti je toto chápání-jednostranné. U papírového vzduchového filtru motoru nepoužívejte k čištění prachu na něm žádný olej. Stačí jemně poklepat rukou nebo vyfouknout vysokotlaký- vzduch z vnitřní a vnější strany filtru. U kožených dílů není potřeba je čistit olejem, stačí je otřít čistým hadrem.